IFM Electronic LR2059 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 51

background image

33

UK

10.2 Explanation of the menu
10.2.1 Main menu [I]

tREF

Carry out tank adjustment.

Menu item only visible if [LEnG] ≥ 260 mm and [Prob] = [rod].

SP1 / rP1

Set point 1 / reset point 1 at which OUT1 switches.

Menu item only visible if hysteresis function is selected ([ou1] = [H..]).

FH1 / FL1

Upper / lower limit for the acceptable range within which OUT1 switches.

Menu item only visible if window function is selected ([ou1] = [F..]).

ASP2

Analogue start point 2: measured value at which the analogue start value is

provided. The analogue start value is set with parameter [ou2]. Menu item

only visible if analogue output is selected ([ou2] = [I] or [InEG]).

AEP2

Analogue end point 2: measured value at which the analogue end value is

provided. The analogue end value is set with parameter [ou2]. Menu item

only visible if analogue output is selected ([ou2] = [I] or [InEG]).

SP2 / rP2

Set point 2 / reset point 2 at which OUT2 switches.

Menu item only visible if hysteresis function is selected ([ou1] = [H..]).

FH2 / FL2

Upper / lower limit for the acceptable range within which OUT2 switches.

Menu item only visible if window function is selected ([ou1] = [F..]).

EF

┘

Extended functions / opening of menu level 2

10.2.2 EF level (extended functions) [II]

rES

Restore the factory setting.

CFG

┘

Open the submenu CFG (configuration).

ENV

┘

Open the submenu ENV (environment parameter).

SIM

┘

Open the submenu SIM (simulation).

«
...
31
32
33
34
35
...
»

Содержание LR2059




















































Отзывы:

Нет отзывов

Похожие инструкции для LR2059

Бренд: Hamax Страницы: 74

Бренд: Keating Of Chicago Страницы: 2

Бренд: LaserTrack Страницы: 12

Бренд: FEIYUTECH Страницы: 8

Бренд: FeiYu Tech Страницы: 2

Бренд: FeiYu Tech Страницы: 2

Бренд: FEIYUTECH Страницы: 26

Бренд: IDS Страницы: 22

Alerts TX60U-IT

Бренд: La Crosse Technology Страницы: 3

Бренд: Nautronic Страницы: 7

Бренд: NAPCO Страницы: 16

Бренд: X4-Life Страницы: 2

Бренд: Yolink Страницы: 27

Бренд: GBRacing Страницы: 2

Бренд: Metra Electronics Страницы: 12

Бренд: Halfords Страницы: 4

Бренд: Heitronic Страницы: 12

Бренд: hepco & becker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды