IFM Electronic efector300 SM0510 Скачать руководство пользователя страница 36

Страница: 36 / 45

10.4.5 Time-controlled counter-reset

► Select [rTo] and set the requested value (intervals of hours, days or

weeks)�

> The counter is reset automatically with the value now set�

10.4.6 Deactivation of the counter reset

► Select [rTo] and set [OFF]�

> The meter is only reset after overflow (= factory setting)�

10.4.7 Configure counter reset using an external signal

► Select [OU2] and set [InD]�

► Select [DIn2] and set the reset signal:

-[HIGH] = reset for high signal,

-[LOW] = reset for low signal,

-[+EDG] = reset for rising edge,

-[-EDG] = reset for falling edge�

10.5 Settings for temperature monitoring
10.5.1 Settings for limit value monitoring with OUT2

► Select [SEL2] and set [TEMP]�

► Select [OU2] and set the switching function�

-[Hno] = hysteresis function/NO,

-[Hnc] = hysteresis function/NC,

-[Fno] = window function/NO,

-[Fnc] = window function/NC�

► Select [SP2] and set the value at which the output switches�

► Select [rP2] and set the value at which the output switches off�

10.5.2 Setting the analogue value for temperature

► Select [SEL2] and set [TEMP]�

► Select [OU2] and set the function:

-[I] = temperature-proportional current signal (4…20 mA);

-[U] = temperature-proportional voltage signal (0…10 V)�

► Select [ASP2] and set the value at which the minimum value is provided�

► Select [AEP2] and set the value at which the maximum value is pro-

vided�

Содержание efector300 SM0510














































Результаты поиска

Содержание efector300 SM0510

Отзывы:

Бренды по названию

Популярные бренды

IFM Electronic efector300 SM0510, Руководство по эксплуатации

Результаты поиска

Содержание efector300 SM0510

Отзывы:

Бренды по названию

Популярные бренды