IFM Electronic efector 300 SU9001 Скачать руководство пользователя

Страница: 24 / 31

9.6.2 Reset all parameters to the factory setting

►

Select [rES], then press [Set] and keep it pressed until

[----] is dis-

played�

►

Press [Mode/Enter] briefly�

The factory setting is listed at the end of the instructions (→ 13 Factory

setting)�

It makes sense to write your own settings in this table before executing the

function�

9.7 Setting of the preset meter / pulse value (ImPS)

5 setting ranges are available:

LED

Display

in steps of

Value

0 0 0� 2 ��

9 9 9� 8

0�2 gal

0�2��999,8 gal

1 0 0 0 ��

9 9 9 9

1 gal

1 000��9 999 gal

3 + 5

1 0� 0 0 ��

9 9� 9 9

10 gal

10 000��99 990 gal

3 + 5

1 0 0� 0 ��

9 9 9� 9

100 gal

100 000��999 900 gal

3 + 5

1 0 0 0 ��

9 0 0 0

1000 gal

1 000 000��9 000 000 gal

Setting operation

► Set [OU1] to [ImP] (→ 9.3.2).

►

Press [Mode/Enter] until [ImPS] is displayed�

►

Press [Set] and keep it pressed�

> The current numerical value flashes for 5 s, then one of the 4 digits becomes

active (digit flashes, can be changed)�

►

Set the requested value as indicated in the following table�

►

First select the requested setting range� Then set the figure from the left digit to the

right digit�

►

Press [Mode/Enter] briefly when all 4 digits are set�

As soon as the first digit flashes there are 3 options:

►

Press [Set] once�

The flashing digit is increased� 9 is followed by 0 - 1 - 2, etc�

8 1� 2 3

1 x [Set] pressed 9 1� 2 3
1 x [Set] pressed 0 1� 2 3
1 x [Set] pressed 1 1� 2 3

Содержание efector 300 SU9001
































Результаты поиска

Содержание efector 300 SU9001

Отзывы:

Похожие инструкции для efector 300 SU9001

Бренды по названию

Популярные бренды

IFM Electronic efector 300 SU9001, Руководство по эксплуатации

Результаты поиска

Содержание efector 300 SU9001

Отзывы:

Похожие инструкции для efector 300 SU9001

Бренды по названию

Популярные бренды