IFM Electronic efector 300 SU9001 Скачать руководство пользователя | Manualshive

Страница: 22 / 31

background image

22

9.4.2 Scaling of the analogue value for temperature

►

Select [SEL2] and set [TEMP]�

►

Select [OU2 ] and set the function:

[I] = current signal proportional to temperature (4…20 mA);

[U] = voltage signal proportional to temperature (0…10 V)�

►

Select [ASP] and set the value at which the minimum output value is

provided�

►

Select [AEP] and set the value at which the maximum output value is

provided�

9.5 User settings (optional)
9.5.1 Determine the standard unit of measurement for volumetric flow

►

Select [Uni] and set the unit of measurement: [GPm] or [GPh]�

The setting only has an effect on the volumetric flow value� The counter

values (consumed quantity) are automatically displayed in the unit of meas-

urement providing the highest accuracy�

9.5.2 Configuration of the standard display

►

Select [SELd] and determine the standard process category�

[FLOW] = display shows the current volumetric flow value in the stand-

ard unit of measurement�

-[TOTL] = display indicates the current meter count in gal or 1000 gal�

-

[TEMP] = display indicates the current medium temperature in °F.

►

Select [diS] and determine the update rate and orientation of the display:

[d1] = update of the measured values every 500 ms�

[d2] = update of the measured values every 1000 ms�

[d3] = update of the measured values every 2000 ms�

[rd1], [rd2], [rd3] = display as for d1, d2, d3; rotated by 180°.

[OFF] = the display is switched off in the operating mode�

9.5.3 Setting the output logic

►

Select [P-n] and set [PnP] or [nPn]�

9.5.4 Calibration of the curve of measured values

►

Select [CGA] and set the value between 60 % und 140 % einstellen

(100 % = factory preset)�

«
...
20
21
22
23
24
...
»

Содержание efector 300 SU9001
































Отзывы:

Нет отзывов

Похожие инструкции для efector 300 SU9001

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 54

Бренд: AAT Страницы: 6

Бренд: Kargo Master Страницы: 13

Бренд: Kargo Master Страницы: 21

Бренд: Kargo Master Страницы: 4

Бренд: Karel Страницы: 56

Бренд: M7 SPEED Страницы: 11

Бренд: UMBRA RIMORCHI Страницы: 18

Бренд: Vaisala Страницы: 2

Бренд: kellermann Страницы: 2

Бренд: Chariot Carriers Страницы: 3

Бренд: Trail-Gator Страницы: 44

Pocket Dual Catchmon

Бренд: Megacom Страницы: 2

Бренд: V8 equipment Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды