IFM Electronic efector 300 SU8001 Скачать руководство пользователя страница 27

Страница: 27 / 31

10.3 Error indication

[SC1]

Short circuit in OUT1�

[SC2]

Short circuit in OUT2�

[SC]

Short circuit in both outputs�

[OL]

Detection zone of volumetric flow or temperature exceeded:

measured value between 120 % and 130 % of VMR�

[UL]

Below the detection zone of temperature:

measured value below 14°F.

[Err]

- Unit faulty / malfunction�

- Measured value greater than 130 % of VMR�

[SEnS] Sensor indicates incorrect measurement� For more detailed diagnosis / fault

assessment:

►

Press [Set] briefly�

> The latest measured values are displayed�

[IOE]

Flow sensor faulty�

[Loc]

Setting pushbuttons locked, parameter change rejected�

VMR = final value of the measuring range

10.4 General operating conditions

►

Avoid deposits, accumulated gas and air in the pipe system�

Greater amounts of accumulated gas and air in the medium or unit generally lead

to the display [SEnS]�

For medium temperatures over 50 °C (122 °F) some parts of the housing

can heat up to over 65 °C (140 °F).

►

In this case do not touch the unit�

►

Protect the housing against contact with flammable substances and uninten-

tional contact�

►

Do not press the pushbuttons manually; instead use an object�

Содержание efector 300 SU8001
































Результаты поиска

Содержание efector 300 SU8001

Отзывы:

IFM Electronic efector 300 SU8001, Руководство по эксплуатации, Страница: 27 / 31

Результаты поиска

Содержание efector 300 SU8001

Отзывы: