IFM Electronic Efector 300 SI0556 Скачать руководство пользователя страница 5

Страница: 5 / 15

4 Installation

Using process adapters the unit can be adapted to different process connections

•

Adapters have to be ordered separately as accessories

A correct fit of the unit and ingress resistance of the connection are only

ensured using ifm adapters

•

For small flow rates ifm adapter blocks are available

4.1 Installation location

General

•

The sensor tip is to be completely sur-

rounded by the medium

•

Insertion depth of the sensor: minimum

12 mm

Recommended

•

For horizontal pipes: mounting from

the side

•

For vertical pipes: mounting in the rising

pipe

Conditional

•

Horizontal pipe /mounting from the bot-

tom: if the pipe is free from build-up

•

Horizontal pipe /mounting from the

top: if the pipe is completely filled with

medium

To avoid

•

The sensor tip must not be in contact

with the pipe wall

•

Do not mount in downpipes that are

open at the bottom!

Содержание Efector 300 SI0556
















Результаты поиска

Содержание Efector 300 SI0556

Отзывы:

Похожие инструкции для Efector 300 SI0556

Бренды по названию

Популярные бренды

IFM Electronic Efector 300 SI0556, Руководство по эксплуатации

Результаты поиска

Содержание Efector 300 SI0556

Отзывы:

Похожие инструкции для Efector 300 SI0556

Бренды по названию

Популярные бренды