manualshive.com logo in svg

IFM Electronic Efector 100 GM505S, Руководство по эксплуатации, Страница: 20 / 21

Поделиться
Скачать
IFM Electronic Efector 100 GM505S Скачать руководство пользователя страница 20

20

12  Troubleshooting

LED display → 9�6

Problem

Possible cause

Troubleshooting

No LED display

No voltage supply

Apply voltage 

Power LED flashes 

and sensor does not 

switch

• Undervoltage

• Overvoltage

Correct the voltage  

(→ 11 Technical data)

Power LED off and 

signal LED flashes

Internal or external fault

• Undamp / damp

• Power off / on

• Replace the unit

• Check wiring / connections

• Check external electronics (e�g� 

G150xS or PLC)

13  Maintenance, repair and disposal

If used correctly no maintenance and repair measures are necessary� 

Only the manufacturer is allowed to repair the unit� 

After use dispose of the unit in an environmentally friendly way in accordance with 

the applicable national regulations� 

14  Approvals / standards

The following standards and directives have been applied:
•  2006/42/EC European machinery directive
•  2004/108/EC EMC Directive
•  DIN EN 954-1 (1996) category 4, safety of machinery, safety-related parts of 

control systems (valid until 31 December 2011)

•  EN ISO 13849-1: 2008 PL e, safety of machinery, safety-related parts of control 

systems

•  IEC 60947-5-2 (2008) low-voltage switchgear: control circuit devices and 

switching elements - proximity switches

•  IEC 61508 (2000)
•  UL 508

Содержание Efector 100 GM505S






















Отзывы:

Нет отзывов