IEI Technology TANK-870AI SERIES Скачать руководство пользователя

Страница: 55 / 137

TANK-870AI Embedded System

Page 41

Figure 3-31: Power Connectors

LED Indicator

Description

Power LED1 (Breathing Orange)

Standby mode.

Power LED2 (Solid blue)

Power-on mode.

Table 3-4: Power LED Indicators Description

NOTE:

The power LED turns off when the power cable is unplugged from the

system.

3.9.1 ACC ON Mode

1. The TANK-870AI series supports single power input and also can be simultaneously

connected to two power sources. When both power connectors are connected to

power sources with 9 V~36 V power input, the one with higher voltage will supply

power to the system.

2. If ACC signal is low, the system will not boot up. If ACC ON signal is high (9 V~36 V),

the system will boot up and work normally.

Содержание TANK-870AI SERIES










































































































































Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды

IEI Technology TANK-870AI SERIES, Руководство пользователя

Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды