IEI Technology TANK-870AI SERIES Скачать руководство пользователя

Страница: 42 / 137

TANK-870AI Embedded System

Page 28

3.6.4 Digital Input/Output Connector

The digital I/O connector provides programmable input and output for external devices.

The pinouts for the digital I/O connector are listed in the table below.

Figure 3-11: DIO Connector

3.6.5 HDMI/DP Connector

To connect the HDMI/DP devices, please plug in HDMI/DP connector in the right direction

as shown below:

Figure 3-12: HDMI/DP Connection

3.6.6 LAN Connectors

The LAN connectors allow connection to an external network.

Step 1:

Locate the RJ-45 connectors

. The locations of the RJ-45 connectors are

shown in

Figure 1-3

Step 2:

Align the connectors.

Align the RJ-45 connector on the LAN cable with one of

the RJ-45 connectors on the TANK-870AI series. See

Figure 3-13

Содержание TANK-870AI SERIES










































































































































Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды

IEI Technology TANK-870AI SERIES, Руководство пользователя

Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды