IEI Technology TANK-870AI SERIES Скачать руководство пользователя

Страница: 25 / 137

TANK-870AI Embedded System

Page 11

The rated voltage and current of the backplanes are listed below.

Rated Voltage

Rated Current

+5 V

4.0 A

+12 V

2.5 A

-12 V

0.1 A

+3.3 V

5.0 A

Table 1-5: Rated Voltage and Current

WARNING:

The system default power is 120 W. The maximum total power of the

backplane to support expansion cards is 45 W. The power of the

selected expansion cards can not exceed the max. power (45 W),

otherwise, the system may be unstable.

NOTE:

When using an expansion card with high power consumption, it is

recommended to install an external power supply to the power input

connector on the backplane.

The backplane support standard PCI/PCIe cards with maximum

dimensions (WxL):110 x 230 mm.

The TANK-870-Q170 provides the most convenient 4-pin internal power connector for

add-on card usage, adding more flexibility to the embedded system in industrial

environment. The internal power connector supports 5V@3A or 12V@3A power supply.

Содержание TANK-870AI SERIES










































































































































Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды

IEI Technology TANK-870AI SERIES, Руководство пользователя

Результаты поиска

Содержание TANK-870AI SERIES

Отзывы:

Похожие инструкции для TANK-870AI SERIES

Бренды по названию

Популярные бренды