IEI Technology PCISA-LX Скачать руководство пользователя страница 98

Страница: 98 / 214

Page 98

IEI® Technology, Corp

PCISA-LX CPU Card

All Errors

Whenever BIOS detects a non-fatal error the

system is stopped and the user prompted.

No Errors

The system boot is not stopped for any errors

that may be detected.

All, But Keyboard

EFAULT

The system boot does not stop for a keyboard

error; it stops for all other errors.

All, But Diskette

The system boot does not stop for a disk

error; it stops for all other errors.

All, But Disk/Key

The system boot does not stop for a keyboard

or a disk error; it stops for all other errors.

Base Memory:

The

Base Memory

is NOT user configurable. The POST determines the amount of base

(or conventional) memory installed in the system. The value of the base memory is

typically 512K for systems with 512K memory installed, or 640K for systems with 640K or

more memory installed.

Extended Memory

The

Extended Memory

is NOT user configurable. The BIOS determines how much

extended memory is present during the POST. This is the amount of memory above 1MB

located in the memory address map of the CPU.

Total Memory

The

Total Memory

is NOT user configurable.

5.2.1 IDE Primary Master/Slave

Use the

IDE Primary Master/Slave

menu (

BIOS Menu 3

) to set or change the

master/slave IDE configurations.

Содержание PCISA-LX























































































































































































































Результаты поиска

Содержание PCISA-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology PCISA-LX, Руководство пользователя

Результаты поиска

Содержание PCISA-LX

Отзывы:

Бренды по названию

Популярные бренды