IEI Technology PCISA-LX Скачать руководство пользователя страница 84

Страница: 84 / 214

Page 84

IEI® Technology, Corp

PCISA-LX CPU Card

4.9 Jumper Settings

NOTE:

A jumper is a metal bridge

that is used to close an

electrical circuit. It consists of

two metal pins and a small

metal clip (often protected by

a plastic cover) that slides

over the pins to connect

them. To CLOSE/SHORT a

jumper means connecting the pins of the jumper with the

plastic clip and to OPEN a jumper means removing the plastic

clip from a jumper.

Jumper

Before the PCISA-LX is installed in the system, the jumpers must be set in accordance

with the desired configuration. The PCISA-LX CPU card has five on-board jumpers.

Description

Label

Type

AT power select

JP5

2-pin header

COM3 RS-422/485 select

JP1

3-pin header

LCD clock select

JP3

3-pin header

LCD voltage select

JP2

3-pin header

PCI VIO voltage select

JP4

3-pin header

Figure 4-3

shows the PCISA-LX jumper locations.

Содержание PCISA-LX























































































































































































































Результаты поиска

Содержание PCISA-LX

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology PCISA-LX, Руководство пользователя

Результаты поиска

Содержание PCISA-LX

Отзывы:

Бренды по названию

Популярные бренды