IEI Technology NANO-ULT5 Скачать руководство пользователя страница 125

Страница: 125 / 147

NANO-ULT5 SBC

Page 111



Quiet Boot [Enabled]

Use the

Quiet Boot

BIOS option to select the screen display when the system boots.



Disabled

Normal POST messages displayed



Enabled

EFAULT

OEM Logo displayed instead of POST messages



Launch PXE OpROM [Disabled]

Use the

Launch PXE OpROM

option to enable or disable boot option for legacy network

devices.



Disabled

EFAULT

Ignore all PXE Option ROMs



Enabled

Load PXE Option ROMs.



Option ROM Messages [Force BIOS]

Use the

Option ROM Messages

option to set the Option ROM display mode.



Force
BIOS

EFAULT

Sets display mode to force BIOS.



Keep
Current

Sets display mode to current.



UEFI Boot [Disabled]

Use the

UEFI Boot

option to enable or disable to boot from the UEFI devices.



Disabled

EFAULT

Boot from UEFI devices is disabled.



Enabled

Boot from UEFI devices is enabled.



Boot Option Priority

Use the

Boot Option Priority

function to set the system boot sequence from the available

devices. The drive sequence also depends on the boot sequence in the individual device
section.

Содержание NANO-ULT5




















































































































































Результаты поиска

Содержание NANO-ULT5

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology NANO-ULT5, Руководство пользователя

Результаты поиска

Содержание NANO-ULT5

Отзывы:

Бренды по названию

Популярные бренды