IEI Technology Nano-PV-D4251 Скачать руководство пользователя

Страница: 95 / 153

NANO-PV-D4251/N4551/D5251 EPIC SBC

Page 82

5.3.6.2 IrDA Configuration

Use the

IrDA Configuration

menu (

BIOS Menu 9

) to configure the serial port n.

Advanced

IrDA Configuration

IrDA [Enabled]

Device Settings

IO=2E0h; IRQ=10

Change Settings

[Auto]

Enable or Disable IrDA

---------------------

ÅÆ

: Select Screen

↑

↓

: Select Item

Enter

Select

F1 General

Help

F2 Previous

Values

F3 Optimized
Defaults
F4 Save

ESC Exit

BIOS Menu 10: IrDA Configuration Menu

IrDA [Enabled]

Use the

IrDA

option to enable or disable the infrared function.

Disabled

Disable the infrared function

Enabled D

EFAULT

Enable the infrared function

Change Settings [Auto]

Use the

Change Settings

option to change the IrDA I/O port address and interrupt

address.

Auto D

EFAULT

The IrDA I/O port address and interrupt address are

automatically detected.

IO=2E0h;

IRQ=10

IrDA I/O port address is 2E0h and the interrupt

address is IRQ10

IO=2C0h;

IRQ=10, 11

IrDA I/O port address is 2C0h and the interrupt

address is IRQ10, 11

Содержание Nano-PV-D4251


























































































































































Результаты поиска

Содержание Nano-PV-D4251

Отзывы:

Похожие инструкции для Nano-PV-D4251

Бренды по названию

Популярные бренды

IEI Technology Nano-PV-D4251, Руководство пользователя

Результаты поиска

Содержание Nano-PV-D4251

Отзывы:

Похожие инструкции для Nano-PV-D4251

Бренды по названию

Популярные бренды