IEI Technology Nano-PV-D4251 Скачать руководство пользователя

Страница: 66 / 153

NANO-PV-D4251/N4551/D5251 EPIC SBC

Page 53

Jumper Settings:

See

Table 4-11

Jumper Location:

See

Figure 4-11

This jumper selects the voltage supplied to the PCI-104 expansion module.

Setting Description

1-2 +5.0

2-3

+3.3 V

Table 4-11: PCI-104 Voltage Jumper Settings

Figure 4-11: PCI-104 Voltage Jumper Location

4.6 Chassis Installation

4.6.1 Airflow

WARNING:

Airflow is critical to the cooling of the CPU and other onboard

components. The chassis in which the NANO-PV-D4251/N4551/D5251

must have air vents to allow cool air to move into the system and hot air

to move out.

The NANO-PV-D4251/N4551/D5251 must be installed in a chassis with ventilation holes

on the sides allowing airflow to travel through the heat sink surface. In a system with an

individual power supply unit, the cooling fan of a power supply can also help generate

airflow through the board surface.

Содержание Nano-PV-D4251


























































































































































Результаты поиска

Содержание Nano-PV-D4251

Отзывы:

Похожие инструкции для Nano-PV-D4251

Бренды по названию

Популярные бренды

IEI Technology Nano-PV-D4251, Руководство пользователя

Результаты поиска

Содержание Nano-PV-D4251

Отзывы:

Похожие инструкции для Nano-PV-D4251

Бренды по названию

Популярные бренды