IEI Technology NANO-6613 Скачать руководство пользователя страница 92

Страница: 92 / 174

-92

IEI

Technology, Corp

ZIP

LS-120

LBA/Large Mode [Auto]

The

LBA/Large Mode

BIOS option disables or auto detects LBA (Logical Block

Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the

maximum drive capacity is 137 GB.

Disabled

This selection prevents the BIOS from using the LBA

mode control on the specified channel.

Auto

(Default)

This option allows the BIOS to auto detect the LBA mode

control on the specified channel.

Block (Multi Sector Transfer) [Auto]

Disabled

Selecting this option prevents the BIOS from using

Multi-Sector Transfer on the specified channel. The data

to and from the device occurs one sector at a time.

Auto

(Default)

Selecting this value to allows the BIOS to auto detect the

device support for Multi-Sector Transfers on the specified

channel. If supported. Select this value to allow the BIOS

to auto detect the number of sectors per block for transfer

from the hard disk drive to the memory. The data transfer

to and from the device occurs multiple sectors at a time.

PIO Mode [Auto]

The

PIO Mode

option selects the IDE PIO (Programmable I/O) mode program timing

cycles between the IDE drive and the programmable IDE controller. As the PIO mode

increases, the cycle time decreases.

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 92 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: