IEI Technology NANO-6613 Скачать руководство пользователя страница 91

Страница: 91 / 174

-91

NANO-6613 Motherboard

Device

: Lists the device type (e.g. hard disk, CD-ROM etc.)

Vendor

: Lists the device manufacturer

Size

: The size of the device.

LBA Mode

: Indicates whether the LBA (Logical Block Addressing) is a

method of addressing data on a disk drive is supported or not.

Block Mode

: Block mode boosts IDE drive performance by increasing the

amount of data transferred. Only 512 bytes of data can be transferred per

interrupt if block mode is not used. Block mode allows transfers of up to 64 KB

per interrupt.

PIO Mode

: Indicates the PIO mode of the installed device.

Async DMA

: Indicates the highest Asynchronous DMA Mode that is

supported.

Ultra DMA

: Indicates the highest Synchronous DMA Mode that is supported.

S.M.A.R.T.

: Indicates whether or not the Self-Monitoring Analysis and

Reporting Technology protocol is supported.

Type [Auto]

The

Type

BIOS option determines the type of device that the AMIBIOS attempts to boot

from after the Power-On Self-Test (POST) has completed.

Not Installed

Selecting this value prevents the BIOS from searching

for an IDE disk drive on the specified channel.

Auto

(Default)

This selection enables the BIOS to auto detect the

IDE disk drive type attached to the specified channel.

This setting should be used if an IDE hard disk drive is

attached to the specified channel.

CD/DVD

The CD/DVD option specifies that an IDE CD-ROM

drive is attached to the specified IDE channel. The

BIOS does not attempt to search for other types of

IDE disk drives on the specified channel.

ARMD

This option specifies an ATAPI Removable Media

Device. These include, but are not limited to:

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 91 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: