IEI Technology NANO-6613 Скачать руководство пользователя страница 75

Страница: 75 / 174

-75

NANO-6613 Motherboard

For more information visit the IEI webstie (

www.ieiworld.com

) or contact an IEI sales

representative.

To install the module, follow the instructions below.

Step 1:

Align the PCI-104 connector with the corresponding connector on a compatible

module.

Step 2:

Gently push the embedded module down to ensure the connectors are properly

connected.

4.3.4 DIMM Module Installation

4.3.4.1 Purchasing the Memory Module

WARNING!

When purchasing the SODIMM modules, make sure the modules are

compatible with the SODIMM slot specified in

Section 2.5 Memory

Support

WARNING!

The board supports DDR1 SODIMM modules only. DDR1 and DDR2

are not compatible. If a DDR2 SODIMM module is installed, the system

may be damaged and become inaccessible. Please only use DDR1

SODIMM modules.

4.3.4.2 SODIMM Module Installation

The NANO-6613 embedded module has one 200-pin SODIMM socket. To install the

SODIMM module, follow the instructions below.

Step 3:

Turn the NANO-6613 over so that the SODIMM socket is facing up.

Step 4:

Push the SODIMM chip into the socket at an angle. (See

Figure 4-6

)

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 75 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: