IEI Technology NANO-6613 Скачать руководство пользователя страница 69

Страница: 69 / 174

-69

NANO-6613 Motherboard

components.

4.2 Unpacking

NOTE:

If any of the items listed below are missing when the NANO-6613 is

unpacked, do not proceed with the installation and contact the NANO-6613

reseller or vendor.

4.2.1 Unpacking Precautions

Before installing the NANO-6613, unpack the motherboard. Some components on

NANO-6613 are very sensitive to static electricity and can be damaged by a sudden rush

of power. To protect it from being damaged, follow these precautions:

The user should ground them self to remove any static charge before

touching the NANO-6613. To do so wear a grounded wrist strap at all times or

frequently touch any conducting materials that is connected to the ground.

Handle the NANO-6613 by its edges. Do not touch the IC chips, leads or

circuitry if not necessary.

Do not place a PCB on top of an anti-static bag. Only the inside of the bag is safe from

static discharge.

4.2.2 Checklist

When unpacking the NANO-6613, please make sure that the package contains the

following items.

1 x NANO-6613 single board computer

1 x IDE flat cable

2 x SATA cables

1 x SATA power cable

2 x RS232 cables

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 69 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: