IEI Technology NANO-6613 Скачать руководство пользователя страница 68

Страница: 68 / 174

-68

IEI

Technology, Corp

4.1 Installation Considerations

NOTE:

The following installation notices and installation considerations should be

read and understood before the motherboard is installed. All installation

notices pertaining to the installation of the motherboard should be strictly

adhered to. Failing to adhere to these precautions may lead to severe

damage of the motherboard and injury to the person installing the

motherboard.

4.1.1 Installation Notices

Before and during the installation of the NANO-6613, please

the following:

Read the user manual

The user manual provides a complete description of the NANO-6613,

installation instructions and configuration options.

Wear an electrostatic discharge cuff (ESD)

Electronic components are easily damaged by ESD. Wearing an ESD cuff

removes ESD from the body and helps prevent ESD damage.

Place the motherboard on an antistatic pad

When installing or configuring the motherboard, place it on an antistatic

pad. This helps to prevent potential ESD damage.

Turn off all power to the NANO-6613

When working with the motherboard, make sure that it is disconnected

from all power supplies and that no electricity is being fed into the system.

Before and during the installation of the NANO-6613

DO NOT:

remove any of the stickers on the PCB board. These stickers are required for

warranty validation.

use the product before verifying all the cables and power connectors are

properly connected.

allow screws to come in contact with the PCB circuit, connector pins, or its

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 68 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: