IEI Technology NANO-6613 Скачать руководство пользователя страница 60

Страница: 60 / 174

-60

IEI

Technology, Corp

3.4 Onboard Jumpers

NOTE:

A jumper is a metal bridge that is

used to close an electrical circuit. It

consists of two metal pins and a small

metal clip (often protected by a plastic

cover) that slides over the pins to

connect them. To CLOSE/SHORT a

jumper means connecting the pins of

the jumper with the plastic clip and to

OPEN a jumper means removing the

plastic clip from a jumper.

Figure 3-22 Jumper

The NANO-6613 motherboard has five onboard jumpers. The jumpers are described in

Table 3-29

Description

Label

Type

Clear CMOS

3-pin header

CPU FSB setting

2-pin header

CPU frequency setting

2-pin header

LCD voltage setup

6-pin header

COM2 setup (RS-232/485)

3-pin header

Table 3-29: Onboard Jumpers

3.4.1 Clear CMOS Jumper

Jumper Label:

Jumper Type:

3 pin header

Jumper Settings:

See Table 3-30

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 60 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: