IEI Technology NANO-6613 Скачать руководство пользователя страница 58

Страница: 58 / 174

-58

IEI

Technology, Corp

Figure 3-21: RJ-45 Ethernet Connector

The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green

LED indicates activity on the port and the yellow LED indicates the port is linked. See

Table 3-26

STATUS DESCRIPTION STATUS DESCRIPTION

GREEN Activity

YELLOW

Linked

Table 3-26: RJ-45 Ethernet Connector LEDs

3.3.3 Keyboard/Mouse Connector

CN Label:

KB/PS1

CN Type:

PS/2 connector

CN Location:

See Figure 3-20 (labeled number 6)

3.3.4 Serial Port Connectors

CN Label:

COM1

CN Type:

DB-9

CN Location:

See Figure 3-20 (labeled number 1)

CN Pinouts:

See Table 3-27

The serial ports (COM1) can be connected to a serial communications device directly.

PIN

NO. DESCRIPTION PIN

NO.

DESCRIPTION

1 DCD1

6 DSR1

2 RX1

7 RTS1

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 58 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: