IEI Technology NANO-6613 Скачать руководство пользователя страница 28

Страница: 28 / 174

-28

IEI

Technology, Corp

are also mounted on the northbridge and southbridge chipsets to ensure the operating

temperature of these chips remain low.

2.14 Audio Codec

The NANO-6613 has an integrated REALTEK ALC655 CODEC. The ALC655 CODEC is a

16-bit, full-duplex AC'97 Rev. 2.3 compatible six-channel audio CODEC designed for PC

multimedia systems, including host/soft audio and AMR/CNR-based designs. Some of the

features of the codec are listed below.

Meets performance requirements for audio on PC99/2001 systems

Meets Microsoft WHQL/WLP 2.0 audio requirements

16-bit Stereo full-duplex CODEC with 48KHz sampling rate

Compliant with AC'97 Rev 2.3 specifications

Front-Out, Surround-Out, MIC-In and LINE-In Jack Sensing

14.318MHz -> 24.576MHz PLL to eliminate crystal

12.288MHz BITCLK input

Integrated PCBEEP generator to save buzzer

Interrupt capability

Three analog line-level stereo inputs with 5-bit volume control, LINE_IN, CD,

AUX

High-quality differential CD input

Two analog line-level mono inputs: PCBEEP, PHONE-IN

Two software selectable MIC inputs

Dedicated Front-MIC input for front panel applications (software selectable)

Boost preamplifier for MIC input

LINE input shared with surround output; MIC input shared with Center and

LFE output

Built-in 50mW/20ohm amplifier for both Front-out and Surround-Out

External Amplifier Power Down (EAPD) capability

Power management and enhanced power saving features

Supports Power-Off CD function

Adjustable VREFOUT control

Supports 48KHz S/PDIF output, complying with AC'97 Rev 2.3 specifications

Supports 32K/44.1K/48KHz S/PDIF input

Power support: Digital: 3.3V; Analog: 3.3V/5V

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 28 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: