IEI Technology NANO-6613 Скачать руководство пользователя страница 26

Страница: 26 / 174

-26

IEI

Technology, Corp

2 x IDE devices

1 x FDD

1 x CFII slot

2.7.1 SATA Drives

The NANO-6613 supports two, first generation SATA drives with transfer rates of up to

150MB/s

2.7.2 IDE HDD Interfaces

The NANO-6613 southbridge chipset IDE controller supports up to four HDDs with the

following specifications:

Supports PIO IDE transfers up to 16MB/s

Supports Ultra ATA 100/133 devices with data transfer rates up to 133MB/s

2.7.3 Floppy Disk Drive (FDD)

The NANO-6613 CPU Board supports a single FDD. The following FDD formats are

compatible with the board.

5.25”: 360KB and 1.2MB

3.5”: 720KB, 1.44MB and 2.88MB

2.7.4 Compact Flash Support

Standard CF-II cards can be inserted into the compact flash slot on the solder side of the

NANO-6613.

2.8 Serial Ports

The NANO-6613 has four high-speed UART serial ports, configured as COM1, COM2,

COM3 and COM4. The serial ports have the following specifications.

16C550 UART with 16-byte FIFO buffer

115.2Kbps transmission rate

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 26 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: