IEI Technology NANO-6613 Скачать руководство пользователя страница 164

Страница: 164 / 174

-16

164

IEI

Technology, Corp

Figure E-3: Select OS Directory Corresponding to the OS

Step 6:

These directories all contain drivers compatible with different OSes. Select the

directory for the OS used on the system and copy all the files onto a separate

floppy disk drive.

Step 0:

E.2.3 Install SATA Drives

To implement the on-chip RAID function, two SATA drives must be connected to the

system. Use the SATA drive cables that came with the system to connect the SATA

drives.

E.2.4 Configure the SATA Controller in BIOS

To configure the RAID BIOS, follow the steps below:

Step 1:

Turn on the motherboard and enter the BIOS setup utility. Do this by clicking

ELETE

when the system boots up.

Step 2:

Select the

Advanced

settings menus.

Step 3:

Select the

IDE Configuration

sub-menu.

Step 4:

In the

IDE Configuration

sub-menu select the “

Onboard PCI S-ATA

Controller

” option.

Step 5:

Set the “

Onboard PCI S-ATA Controller

” option to the “

Raid Mode

” and hit

NTER

Step 6:

Save the changes and exit the BIOS setup utility. To do this, hit the escape key

and select the

Exit

menu from the top menu bar in the BIOS utility setup.

Step 7:

When the

Exit

menu appears, select the “

Save Changes and Exit

” menu option.

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 164 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: