IEI Technology NANO-6613 Скачать руководство пользователя страница 162

Страница: 162 / 174

-16

162

IEI

Technology, Corp

E.1 Introduction

E.1.1 RAID Support

The SiS964 southbridge chipset integrated controller supports the following three SATA

RAID levels:

JBOD

RAID0

RAID1

E.1.2 What is RAID

RAID, or redundant array of inexpensive disks, is a method of saving data on multiple

disks so that if one of the disks is damaged or destroyed, the data on the disks is not lost.

Only the three RAID levels listed above can be implemented on the system

JBOD stands for Just a Bunch Of Disks. This is not a RAID level. If any thing

happens to one hard drive, all the information on that drive is lost.

RAID0 refers to disk striping. Data is distributed (striped) over multiple disks.

This increases the overall disk performance but the data is not redundantly

stored and therefore any damage to the system disks results in a loss of

information.

RAID1 refers to disk mirroring. The information on one disk is completely

mirrored onto a second disk. The effective storage capacity of the hard disks

is halved but the data on the disks is safe. If one of the disks is destroyed or

damaged in any way the information on that disk is retrievable from the

second disk.

E.2 RAID Setup

E.2.1 Introduction

To setup the RAID, the following procedures must be completed.

Step 4:

Two SATA drives must be installed onto the system.

Step 5:

The RAID BIOS must be configured.

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 162 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: