IEI Technology NANO-6613 Скачать руководство пользователя страница 111

Страница: 111 / 174

-11

NANO-6613 Motherboard

111

PCI/PnP devices

Reserved

The specified DMA is reserved for use by Legacy

ISA devices

Available DMA Channels are:

DM Channel 0

DM Channel 1

DM Channel 3

DM Channel 5

DM Channel 6

DM Channel 7

Reserved Memory Size [Disabled]

The

Reserved Memory Size

BIOS option specifies the amount of memory that should be

reserved for legacy ISA devices.

Disabled

(Default)

No memory block reserved for legacy ISA devices

16K

16KB reserved for legacy ISA devices

32K

32KB reserved for legacy ISA devices

64K

54KB reserved for legacy ISA devices

5.5 Chipset

The Chipset menu (

BIOS Menu 13

) has two sub-menus, NorthBridge Configuration and

SouthBridge Configuration. The NorthBridge Configuration menu configures the

northbridge chipset and the SouthBridge Configuration menu configures the southbridge

chipset.

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 111 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: