IEI Technology NANO-6613 Скачать руководство пользователя страница 106

Страница: 106 / 174

-10

106

IEI

Technology, Corp

Legacy USB Support [Enabled]

The

Legacy USB Support

BIOS option refers to USB mouse and USB keyboard support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded on the system.

Disabled

Legacy

USB

support

disabled

Enabled

(Default) Legacy

USB

support

enabled

USB2.0 Controller Mode [HiSpeed]

The

USB2.0 Controller Mode

BIOS option sets the speed of the USB2.0 controller.

FullSpeed

The controller is capable of operating at full speed

(12Mbits/second)

HiSpeed

(Default)

The controller is capable of operating at high speed

(480Mbits/second)

5.4 PCI/PnP

The

PCI/PnP

menu (

BIOS Menu 12

) configures advanced PCI and PnP settings.

WARNING!

Setting wrong values for the BIOS selections in the PCIPnP BIOS menu

may cause the system to malfunction.

Содержание NANO-6613















































































































































































Результаты поиска

Содержание NANO-6613

Отзывы:

IEI Technology NANO-6613, Руководство пользователя, Страница: 106 / 174

Результаты поиска

Содержание NANO-6613

Отзывы: