IEI Technology KINO-LX Скачать руководство пользователя страница 95

Страница: 95 / 197

Page 95

KINO-LX Motherboard

IDE Master and IDE Slave

When entering setup, BIOS auto detects the presence of IDE devices. The

Standard

CMOS Features

menu shows the status of the auto detected IDE devices. The following

IDE devices are detected and shown in the

Standard CMOS Features

menu:

IDE Primary Master

IDE Primary Slave

IDE device configurations are changed or set in the IDE Configuration menu (

BIOS Menu

). If an IDE device is detected, and one of the above listed two BIOS configuration

options is selected, the IDE configuration options shown in

Section 5.2.1

appear.

Drive A [1.44M, 3.5in]

Use the Drive A configuration to specify the floppy drive type installed in the system. The

floppy drive configuration options are:

None

360K, 5.25 in.

1.2M, 5.25 in.

720K, 3.5 in.

1.44M, 3.5in (Default)

2.88M, 3.5 in.

Drive B [None]

Use the Drive B configuration to specify the floppy drive type installed in the system. The

floppy drive configuration options are:

None (Default)

360K, 5.25 in.

1.2M, 5.25 in.

720K, 3.5 in.

1.44M, 3.5in

2.88M, 3.5 in.

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 95 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: