IEI Technology KINO-LX Скачать руководство пользователя страница 87

Страница: 87 / 197

Page 87

KINO-LX Motherboard

The AT/ATX power connector is used to connect a chassis power On/Off button using an

adapter cable and is configured through the JP6 jumper. The AT/ATX power connector

has two operational modes:

1. Using

ATX

power: AT/ATX power connects to an externally implemented power

switch, and the JP6 jumper should be left open.

2. Using

power: The pins on JP6 are shorted by a jumper cap. JP6 should be

shorted by default as the AMD Southbridge is designed without the consideration

for a power button signal. The shorted JP6 provides a hardware feedback to

initiate the system. The power on/off function is then managed by the AT power

switch button.

JP6 Description

Short

AT Mode (Default)

Open ATX

Mode

Table 4-8: AT/ATX Power Mode Select Jumper Settings

4.7 Chassis Installation

After the DIMM modules have been installed and after the internal peripheral connectors

have been connected to the peripheral devices and the jumpers have been configured,

the KINO-LX can be mounted into chassis.

To mount a board into a chassis, please refer to the chassis user guide that came with the

product.

4.8 Rear Panel Connectors

4.8.1 Keyboard and Mouse Connection

A PS/2 keyboard and a PS/2 mouse can be connected to the appropriate PS/2 connector

on the rear panel.

Содержание KINO-LX






































































































































































































Результаты поиска

Содержание KINO-LX

Отзывы:

IEI Technology KINO-LX, Руководство пользователя, Страница: 87 / 197

Результаты поиска

Содержание KINO-LX

Отзывы: