IEI Technology KINO-ATOM Скачать руководство пользователя страница 98

Страница: 98 / 202

KINO-ATOM Motherboard

Page 80

Figure 5-9: 5.1 Channel Audio Kit

Step 4:

Mount the audio kit onto the chassis

. Once the audio kit is connected to the

KINO-ATOM, secure the audio kit bracket to the system chassis.

Step 5:

Connect the audio devices

. Connect one speaker to the line-in audio jack, one

speaker to the line-out audio jack and a microphone to the mic-in audio jack.

Step 6:

Install the driver

. If the 5.1 channel audio kit is used, the ALC655 Realtek

codec driver must be installed. Refer to

Chapter 7

for driver installation

instructions.

Step 0:

5.8.2 7.1 Channel Audio Kit Installation

NOTE:

This is an optional item that must be ordered separately. For further

information please contact the nearest KINO-ATOM distributor, reseller

or vendor or contact an iEi sales representative directly. Send any

queries to

[email protected]

Содержание KINO-ATOM











































































































































































































Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology KINO-ATOM, Руководство пользователя

Результаты поиска

Содержание KINO-ATOM

Отзывы:

Бренды по названию

Популярные бренды