IEI Technology KINO-690S1 Скачать руководство пользователя страница 137

Страница: 137 / 229

KINO-690S1 Mini-ITX Motherboard

Page 119

19200 8,n,1

09600 8,n,1

NOTE:

Identical baud rate setting musts be set on the host (a management

computer running a terminal software) and the slave

Flow Control [None]

Use the

Flow Control

option to report the flow control method for the console redirection

application.

None D

EFAULT

No control flow,

Hardware

Hardware is set as the console redirection

Software

Software is set as the console redirection

Redirection After BIOS POST [Always]

Use the

Redirection After BIOS POST

option to specify when console redirection should

occur.

Disabled

The console is not redirected after POST

Boot Loader

Redirection is active during POST and during Boot

Loader

Always

EFAULT

Redirection is always active (Some OSes may not

work if set to Always)

Terminal Type [ANSI]

Use the

Terminal Type

BIOS option to specify the remote terminal type.

Содержание KINO-690S1






































































































































































































































Результаты поиска

Содержание KINO-690S1

Отзывы:

IEI Technology KINO-690S1, Руководство пользователя, Страница: 137 / 229

Результаты поиска

Содержание KINO-690S1

Отзывы: