IEI Technology ISIGNAGER - 800WL-N270 Скачать руководство пользователя страница 36

Страница: 36 / 67

iSignager-800WL-N270 Digital Signage Player

Page 28

3.1 System Maintenance Introduction

If the components of the iSignager-800WL-N270 series fail they must be replaced.

Components that can be replaced include:

HDD

Module

SO-DIMM

module

Wireless LAN module

Please contact the system reseller or vendor to purchase the replacement parts. Top

cover removal instructions for the iSignager-800WL-N270 series are described below.

3.2 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the maintenance of the

iSignager-800WL-N270 may result in permanent damage to the

iSignager-800WL-N270 and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the iSignager-800WL-N270. Dry climates are especially susceptible to ESD. It is

therefore critical that whenever the panel PC is accessed internally, or any other electrical

component is handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding

: - Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad

: - When configuring the iSignager-800WL-N270,

place it on an antic-static pad. This reduces the possibility of ESD damaging

the iSignager-800WL-N270.

Содержание ISIGNAGER - 800WL-N270




































































Результаты поиска

Содержание ISIGNAGER - 800WL-N270

Отзывы:

Похожие инструкции для ISIGNAGER - 800WL-N270

Бренды по названию

Популярные бренды

IEI Technology ISIGNAGER - 800WL-N270, Руководство пользователя

Результаты поиска

Содержание ISIGNAGER - 800WL-N270

Отзывы:

Похожие инструкции для ISIGNAGER - 800WL-N270

Бренды по названию

Популярные бренды