IEI Technology IceCare-10W series Скачать руководство пользователя страница 69

Страница: 69 / 107

ICECARE-10W Mobile Sales Assistant

Page 57

5.3.5 SATA Configuration

Use the

SATA Configuration

menu (

583

BIOS Menu 7

) to change and/or set the

configuration of the SATA devices installed in the system.

Advanced

SATA Controller(s)

[Enabled]

SATA Mode Selection

[IDE]

mSATA(M_PCIE3) Port

MRMAJ5A032GC2M

(30.0GB)

Enable or disable SATA
Device.

---------------------



: Select Screen





: Select Item

Enter: Select
+/-: Change Opt.
F1: General

Help

F2: Previous

Values

F3: Optimized

Defaults

F4:

Save & Exit

ESC: Exit

BIOS Menu 7: SATA

Configuration



SATA Controller(s) [Enabled]

Use the

SATA Controller(s)

option to configure the serial ATA controller.



Enabled D

EFAULT

Enables the on-board SATA controller.



Disabled

Disables the on-board SATA controller.



Configure SATA as [AHCI]

Use the

Configure SATA as

option to configure SATA devices as normal IDE devices.



IDE

Configures SATA devices as normal IDE device.



AHCI D

EFAULT

Configures SATA devices as AHCI device.

Содержание IceCare-10W series












































































































Результаты поиска

Содержание IceCare-10W series

Отзывы:

Похожие инструкции для IceCare-10W series

Бренды по названию

Популярные бренды

IEI Technology IceCare-10W series, Руководство пользователя

Результаты поиска

Содержание IceCare-10W series

Отзывы:

Похожие инструкции для IceCare-10W series

Бренды по названию

Популярные бренды