IEI Technology HYPER-BW Скачать руководство пользователя страница 76

Страница: 76 / 102

HYPER-BW

Page 65

Chipset

Intel IGD Configuration

Integrated Graphics Device

[Enabled]

Primary Display

[Auto]

DVMT Pre-Allocated

[256M]

DVMT Total Gfx Mem

[MAX]

Primary IGFX Boot Display

[Auto]

Enable: Enable

Integrated Graphics

Device (IGD) when

selected as the Primary

Video Adaptor. Disable:

Always disable IGD.

---------------------



: Select Screen

↑

↓

: Select Item

Enter Select

+/-: Change Opt.

F1: General Help

F2: Previous Values

F3: Optimized Defaults

F4: Save & Exit

ESC: Exit

BIOS Menu 17:

Integrated Graphics



Integrated Graphics Device [Enabled]

Use the

Integrated Graphics Device

option to enable or disable the Integrated Graphics

Device (IGD) when selected as the Primary Video Adaptor.



Disabled

Disables the Integrated Graphics Device (IGD).



Enabled

EFAULT

Enables the Integrated Graphics Device (IGD).



Primary Dis play [Auto]

Use the

Primary Display

option to select the primary graphics controller the system uses.

The following options are available:



Auto

Default



IGD



PCIe



DVMT Pre-Allocated [256MB]

Use the

DVMT Pre-Allocated

option to set the amount of system memory allocated to the

integrated graphics processor when the system boots. The system memory allocated can

Содержание HYPER-BW







































































































Результаты поиска

Содержание HYPER-BW

Отзывы:

Похожие инструкции для HYPER-BW

Бренды по названию

Популярные бренды

IEI Technology HYPER-BW, Руководство пользователя

Результаты поиска

Содержание HYPER-BW

Отзывы:

Похожие инструкции для HYPER-BW

Бренды по названию

Популярные бренды