IEI Technology HYPER-BW Скачать руководство пользователя страница 56

Страница: 56 / 102

HYPER-BW

Page 45

Key

Function

Decrease the numeric value or make changes

F1 key

General help, only for Status Page Setup Menu and Option
Page Setup Menu

F2 key

Load previous values.

F3 key

Load optimized defaults

F4 key

Save changes and Exit BIOS

Esc key

Main Menu – Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --
Exit current page and return to Main Menu

Table 5-1: BIOS Navigation Keys

5.1.3

Getting Help

When

is pressed a small help window describing the appropriate keys to use and the

possible selections for the highlighted item appears. To exit the Help Window press

the

key again.

5.1.4

Unable to Reboot after Configuration Changes

If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter

5.1.5

BIOS Menu Bar

The

menu bar

on top of the BIOS screen has the following main items:



Main – Changes the basic system configuration.



Advanced – Changes the advanced system settings.



Chipset – Changes the chipset settings.



Boot – Changes the system boot configuration.



Security – Sets User and Supervisor Passwords.



Save & Exit – Selects exit options and loads default settings

Содержание HYPER-BW







































































































Результаты поиска

Содержание HYPER-BW

Отзывы:

Похожие инструкции для HYPER-BW

Бренды по названию

Популярные бренды

IEI Technology HYPER-BW, Руководство пользователя

Результаты поиска

Содержание HYPER-BW

Отзывы:

Похожие инструкции для HYPER-BW

Бренды по названию

Популярные бренды