IEI Technology eKINO-BT Скачать руководство пользователя

Страница: 97 / 157

eKINO-BT Mini-ITX SBC

Page 83

Key

Function

Page Up key

Move to the next page

Page Dn key

Move to the previous page

Esc key

Main Menu – Quit and not save changes into CMOS

Status Page Setup Menu and Option Page Setup Menu --

Exit current page and return to Main Menu

General help, only for Status Page Setup Menu and Option

Page Setup Menu

Load previous values

Load optimized defaults

Save changes and Exit BIOS

Table 5-1: BIOS Navigation Keys

5.1.3 Getting Help

When

is pressed a small help window describing the appropriate keys to use and the

possible selections for the highlighted item appears. To exit the Help Window press

the

key again.

5.1.4 Unable to Reboot after Configuration Changes

If the computer cannot boot after changes to the system configuration are made, CMOS

defaults. Use the clear CMOS button described in

Chapter

5.1.5 BIOS Menu Bar

The

menu bar

on top of the BIOS screen has the following main items:

Main – Changes the basic system configuration.

Advanced – Changes the advanced system settings.

Chipset – Changes the chipset settings.

Security – Sets User and Supervisor Passwords.

Boot – Changes the system boot configuration.

Save & Exit – Selects exit options and loads default settings.

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды