IEI Technology eKINO-BT Скачать руководство пользователя

Страница: 93 / 157

eKINO-BT Mini-ITX SBC

Page 79

Figure 4-22: USB Connector

4.10.5 VGA Monitor Connection

The eKINO-BT has a single female DB-15 connector on the external peripheral interface

panel. The DB-15 connector is connected to a CRT or VGA monitor. To connect a monitor

to the eKINO-BT, please follow the instructions below.

Step 1:

Locate the female DB-15 connector

. The location of the female DB-15

connector is shown in

Chapter 3

Step 2:

Align the VGA connector

. Align the male DB-15 connector on the VGA screen

cable with the female DB-15 connector on the external peripheral interface.

Step 3:

Insert the VGA connector

Once the connectors are properly aligned with the

insert the male connector from the VGA screen into the female connector on the

eKINO-BT. See

Figure 4-23

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды