IEI Technology eKINO-BT Скачать руководство пользователя

Страница: 69 / 157

eKINO-BT Mini-ITX SBC

Page 55

Figure 3-39: VGA Connector

NOTE:

After installing Intel® graphics driver, the two LVDS ports will be set to

the primary display output ports and the VGA port will be disabled. The

reason for this is the eKINO-BT uses two CH7511B chips to convert

DP to LVDS and Intel® graphics driver recognizes the chips and the

two LVDS ports as two devices. In addition, the on-board processor

only supports dual display output, therefore, the display devices can

only be connected to the two LVDS ports, not the VGA port.

If there is a need to change the display output port or set to VGA port

only, please contact IEI for BIOS customization.

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды