IEI Technology eKINO-BT Скачать руководство пользователя

Страница: 26 / 157

eKINO-BT Mini-ITX SBC

Page 12

2.1 Anti-static Precautions

WARNING!

Static electricity can destroy certain electronics. Make sure to follow the

ESD precautions to prevent damage to the product, and injury to the

user.

Make sure to adhere to the following guidelines:

Wear an anti-static wristband

: Wearing an anti-static wristband can prevent

electrostatic discharge.

Self-grounding

: Touch a grounded conductor every few minutes to discharge

any excess static buildup.

Use an anti-static pad

: When configuring any circuit board, place it on an

anti-static mat.

Only handle the edges of the PCB

: Don't touch the surface of the

motherboard. Hold the motherboard by the edges when handling.

2.2 Unpacking Precautions

When the eKINO-BT is unpacked, please do the following:

Follow the anti-static guidelines above.

Make sure the packing box is facing upwards when opening.

Make sure all the packing list items are present.

Содержание eKINO-BT






























































































































































Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды

IEI Technology eKINO-BT, Руководство пользователя

Результаты поиска

Содержание eKINO-BT

Отзывы:

Похожие инструкции для eKINO-BT

Бренды по названию

Популярные бренды