IEI Technology eKINO-945GSE Скачать руководство пользователя страница 93

Страница: 93 / 215

eKINO-945GSE Motherboard

Page 77

Figure 5-5: IDE Cable Connection

Step 6:

Connect the cable to an IDE device

. Connect the two connectors on the other

side of the cable to one or two IDE devices. Make sure that pin 1 on the cable

corresponds to pin 1 on the connector.

Step 0:

5.9.2 SATA Drive Connection

The eKINO-945GSE is shipped with two SATA drive cables and one SATA drive power

cable. To connect the SATA drives to the connectors, please follow the steps below.

Step 1:

Locate the connectors

. The locations of the SATA drive connectors are shown

Chapter 3

Step 2:

Insert the cable connector

. Press the clip on the connector at the end of the

SATA cable and insert the cable connector into the onboard SATA drive

connector. See

Figure 5-6

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 93 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: