IEI Technology eKINO-945GSE Скачать руководство пользователя страница 89

Страница: 89 / 215

eKINO-945GSE Motherboard

Page 73

Pin Setting

Description

Open

640 x 480 (18-bit)

1-2

800 x 480 (18-bit)

3-4

800 x 600 (18-bit)

1-2, 3-4

1024 x 768 (18-bit)

5-6

1280 x 1024 (18-bit)

1-2, 5-6

1400 x 1050 (18-bit)

3-4, 5-6

1400 x 900 (18-bit)

1-2, 3-4, 5-6

1600 x 1200 (18-bit)

Table 5-6: LCD Panel Type Selection Jumper Settings

5.7.6 LVDS Voltage Selection

WARNING:

Permanent damage to the screen and eKINO-945GSE may occur if the

wrong voltage is selected with this jumper. Please refer to the user

guide that cam with the monitor to select the correct voltage.

Jumper Label:

J_VLVDS1

Jumper Type:

3-pin header

Jumper Settings:

See

Table 5-7

Jumper Location:

See

Figure 5-4

The

LVDS Voltage Selection

jumper allows the LVDS screen voltage to be set. The

LVDS Voltage Selection

jumper settings are shown in

Table 5-7

Pin Setting

Description

1-2

3.3 V

2-3

5 V

Table 5-7: LVDS Voltage Selection Jumper Settings

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 89 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: