IEI Technology eKINO-945GSE Скачать руководство пользователя страница 78

Страница: 78 / 215

eKINO-945GSE Motherboard

Page 62

5.1 Anti-static Precautions

WARNING:

Failure to take ESD precautions during the installation of the

eKINO-945GSE may result in permanent damage to the

eKINO-945GSE and severe injury to the user.

Electrostatic discharge (ESD) can cause serious damage to electronic components,

including the eKINO-945GSE. Dry climates are especially susceptible to ESD. It is

therefore critical that whenever the eKINO-945GSE, or any other electrical component is

handled, the following anti-static precautions are strictly adhered to.

Wear an anti-static wristband

: - Wearing a simple anti-static wristband can

help to prevent ESD from damaging the board.

Self-grounding

:- Before handling the board touch any grounded conducting

material. During the time the board is handled, frequently touch any

conducting materials that are connected to the ground.

Use an anti-static pad

: When configuring the eKINO-945GSE, place it on an

antic-static pad. This reduces the possibility of ESD damaging the

eKINO-945GSE.

Only handle the edges of the PCB

:-: When handling the PCB, hold the PCB

by the edges.

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 78 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: