IEI Technology eKINO-945GSE Скачать руководство пользователя страница 147

Страница: 147 / 215

eKINO-945GSE Motherboard

Page 131

6.7.1 Northbridge Chipset Configuration

Use the

Northbridge Chipset Configuration

menu (

BIOS Menu 21

) to configure the

Northbridge chipset settings.

BIOS Menu 22: Northbridge Chipset Configuration

Memory Hole [Disabled]

The

Memory Hole

reserves the memory space between 15 MB and 16 MB for ISA

expansion cards that require a specified area of memory to work properly. If an older ISA

expansion card is used, please refer to the documentation that came with the card to see if

it is necessary to reserve the space.

Disabled D

EFAULT

Memory is not reserved for ISA expansion cards

Enabled

Memory is reserved for ISA expansion cards

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 147 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: