IEI Technology eKINO-945GSE Скачать руководство пользователя страница 145

Страница: 145 / 215

eKINO-945GSE Motherboard

Page 129

BIOS Menu 20: Security

Change Supervisor Password

Use the

Change Supervisor Password

to set or change a supervisor password. The

default for this option is

Not Installed

. If a supervisor password must be installed, select

this field and enter the password. After the password has been added,

Install

appears

next to

Change Supervisor Password

Change User Password

Use the

Change User Password

to set or change a user password. The default for this

option is

Not Installed

. If a user password must be installed, select this field and enter the

password. After the password has been added,

Install

appears next to

Change User

Password

6.7 Chipset

Use the

Chipset

menu (

BIOS Menu 21

) to access the Northbridge and Southbridge

configuration menus

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 145 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: