IEI Technology eKINO-945GSE Скачать руководство пользователя страница 101

Страница: 101 / 215

eKINO-945GSE Motherboard

Page 85

Step 1:

Locate the dual PS/2 connector

. The location of the PS/2 connector is shown

Chapter 3

Step 2:

Insert the keyboard/mouse connector

Insert the PS/2 connector on the end

of the PS/2 y-cable into the external PS/2 connector. See

Figure 5-13

Figure 5-13: PS/2 Keyboard/Mouse Connector

Step 3:

Connect the keyboard and mouse

. Connect the keyboard and mouse to the

appropriate connector. The keyboard and mouse connectors can be

distinguished from each other by looking at the small graphic at the top of the

connector.

Step 0:

5.10.3 Serial Device Connection

The eKINO-945GSE has a single female DB-9 connector on the external peripheral

interface panel for a serial device. Follow the steps below to connect a serial device to the

eKINO-945GSE.

Содержание eKINO-945GSE
























































































































































































































Результаты поиска

Содержание eKINO-945GSE

Отзывы:

IEI Technology eKINO-945GSE, Руководство пользователя, Страница: 101 / 215

Результаты поиска

Содержание eKINO-945GSE

Отзывы: