IEI Technology AFOLUX AFL-315AW/B Скачать руководство пользователя страница 136

Страница: 136 / 198

AFOLUX Kiosk Application Series

Page 120

Restore on AC Power Loss [Power Off]

Use the

Restore on AC Power Loss

BIOS option to specify what state the system

returns to if there is a sudden loss of power to the system.

Power Off

The system remains turned off

Power On

EFAULT

The system turns on

Last State

The system returns to its previous state. If it was on, it

turns itself on. If it was off, it remains off.

Resume on Keyboard/Mouse [Disabled]

Use the

Resume on Keyboard/Mouse

BIOS option to enable activity on the keyboard or

mouse to rouse the system from a suspend or standby state.

Disabled D

EFAULT

Wake event not generated by activity on the

keyboard or mouse

Enabled

Wake event generated by activity on the keyboard or

mouse

Resume on Ring [Disabled]

Use the

Resume on Ring

BIOS option to enable activity on the RI (ring in) modem line to

rouse the system from a suspend or standby state. That is, the system will be roused by

an incoming call on a modem.

Disabled D

EFAULT

Wake event not generated by an incoming call

Enabled

Wake event generated by an incoming call

Resume on PCIE [Enabled]

The

Resume on PCIE

BIOS option specifies if the system is roused from a suspended or

standby state when there is activity on the PCI-Express bus.

Содержание AFOLUX AFL-315AW/B







































































































































































































Результаты поиска

Содержание AFOLUX AFL-315AW/B

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology AFOLUX AFL-315AW/B, Руководство пользователя

Результаты поиска

Содержание AFOLUX AFL-315AW/B

Отзывы:

Бренды по названию

Популярные бренды