IEI Technology AFL-xxA-N270 series Скачать руководство пользователя страница 67

Страница: 67 / 171

AFL-xxA-N270 Series Panel PC

Page 52

Step 18:

Secure the flat panel PC to the interface pad by inserting four retention screws

through the bottom of the mounting arm interface pad and into the flat panel PC.

Step 0:

4.10.4 Cabinet and Rack Installation

The AFL-xxA-N270 series flat panel PC can be installed into a cabinet or rack. The

installation procedures are similar to the panel mounting installation. To do this, please

follow the steps below:

NOTE:

When purchasing the cabinet/rack installation bracket, make sure it is

compatible with both the AFL-xxA-N270 series flat panel PC and the

rack/cabinet into which the AFL-xxA-N270 series is installed.

Step 1:

Slide the rear chassis of the AFL-xxA-N270 series flat panel PC through the

rack/cabinet bracket until the aluminum frame is flush against the front of the

bracket (

Figure 4-22

Figure 4-22: The Rack/Cabinet Bracket

Step 2:

Insert the rack mounting clamps into the pre-formed holes along the edges of

the flat panel PC, behind the ABS/PC plastic frame. There are a total of 4 rack

Содержание AFL-xxA-N270 series












































































































































































Результаты поиска

Содержание AFL-xxA-N270 series

Отзывы:

IEI Technology AFL-xxA-N270 series, Руководство пользователя, Страница: 67 / 171

Результаты поиска

Содержание AFL-xxA-N270 series

Отзывы: