IEI Technology AFL-xxA-N270 series Скачать руководство пользователя страница 121

Страница: 121 / 171

AFL-xxA-N270 Series Panel PC

Page 106

7.1 Available Software Drivers

NOTE:

The content of the CD may vary throughout the life cycle of the product

and is subject to change without prior notice. Visit the IEI website or

contact technical support for the latest updates.

The following drivers can be installed on the system:

Chipset

VGA

Audio

LAN

Touch

screen

Bluetooth

Wireless

Installation instructions are given below.

7.2 Starting the Driver Program

To access the driver installation programs, please do the following.

Step 1:

Insert the CD-ROM that came with the system into a CD-ROM drive attached to

the system.

Step 2:

Click

AFL-xxA-N270 Series

Step 3:

Select the

AFLMB-945GSE-R10

Step 4:

The list of drivers in

Figure 7-1

appears.

Step 4:

Содержание AFL-xxA-N270 series












































































































































































Результаты поиска

Содержание AFL-xxA-N270 series

Отзывы:

IEI Technology AFL-xxA-N270 series, Руководство пользователя, Страница: 121 / 171

Результаты поиска

Содержание AFL-xxA-N270 series

Отзывы: