IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 96 / 170

AFL-xxA-N270 Series Panel PC

Page 82

PWM

The following system parameters and values are shown. The system parameters that are

monitored are:

System Temperatures

: The following system temperatures are monitored

CPU Temperature

System Temperature

Fan Speeds

: The CPU cooling fan speed is monitored.

CPU Fan Speed

Voltages

: The following system voltages are monitored

CPU Core

+1.05V

+3.30V

+5.00V

+12.0 V

+1.5V

+1.8V

5VSB

VBAT

6.3.5 Power Configuration

The

Power Configuration

menu (

BIOS Menu 8

) configures the Advanced Configuration

and Power Interface (ACPI) and Power Management (APM) options.

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды